Nerd’s Eye View: McLaren 720S
Underneath, McLaren employed a number of aero tricks. A diffuser reduces front lift and probably helps direct air to the massive plastic air scoop attached to the lower control arm. The scoop is used to guide cooling air to the front brake ala every performance car these days. A pair of air turning guide vanes is attached to the flat bottom of the car. My assumption is the vanes direct air into the wake left behind the front tire to help reduce drag, reduce air curling under the car, or some other aerodynamic trick.

 

Here’s another view of the flat bottom of the car and the air turning vanes. I believe the big shiny rectangle in the middle of the car is the fuel tank which I think is typically covered by a panel.

 

This plastic duct directs the air from the side scoop into heat exchanger mounted behind it. I’m guessing the hex pattern is to add some stiffness to the plastic. This is the left-hand side of the car (US driver’s side, UK passenger side just to be clear).

 

This view gives a shot of one airflow path into the side plastic duct and the heat exchanger mounted behind it. Man… there are a LOT of fluid lines on this car! The one top line with the flexible black sections is potentially an A/C line. As for the other ones, they are probably some mix of coolant, oil, and maybe some hydraulic suspension lines too. This view gives a good look at the pretty aluminum casting used in the rear structure of the car. I’m sure those ribs in the casting were optimized for weight and strength.

 

This view on the right side of the car shows the tight packaging. It looks like there’s an A/C condenser stacked in front of a radiator with a fan attached on the backside. Squeezed in on the left is a turbo covered with tons of heat shielding. With an A/C line running right by the turbo, the heat shielding is definitely required. Besides, as all you MotoIQ readers know, keeping heat in the turbine housing improves turbo performance.

18 comments

  1. The turning vanes underneath the car are used to create a barrier layer, so in a way, you where correct. It’s used to separate high pressure turbulent airflow from the tyres from the high flowing, non turbulent air from under the car. It does create a slight bit of lift, but helps the rear diffusor. But probbably the most important factor about it: It cancels road noise.

    1. KS, appreciate the insight! So basically the turning vanes create an air curtain to prevent the dirty tire wake from spilling over to the rear diffuser.

  2. Interesting rear swaybar mount gets a feature cast into the subframe. Though I thought a 720S with the Kinetic suspension setup doesn’t have actual swaybar?

    1. Typically McLaren’s have a “Z” bar. The “Z” bar is a 3rd spring for the rear. They look like a sway bar but the arms are opposing(in the shape of a Z). Since the suspension is hydraulic and connected via a pump/module a sway bar is not needed. There is no antiroll bar or z bar in the front.

  3. The black pump things in the last picture will be the secondary air pumps for getting the cats up to temp quicker under cold start conditions, one for each exhaust bank.

    1. Thanks Alex! I am curious how many cars have air pumps. My s2000 has one and I think my dads FC rx7 has one. I don’t recall my evo having one or most other cars I’ve wrenched on. Though maybe I just wasn’t paying attention.

  4. Behhh… those plastic retention clips on the control arms. I wonder 2 things: 1) If the addition of the almost assuredly threaded holes required for the ribbing on those clips to grab onto introduces potential stress risers, thus requiring the control arms to be made thicker/heavier and 2) if McLaren knows that they make zip ties with wiring loom retention loops attached to them

    1. The middle of the section of a beam sees little stress. The top and bottom of the beam see the highest strain. At least, they put holes in the best place to minimize fatigue, but yeah if you hit a curb hard, I’m sure that’s a point of failure.

      Also, zip ties look janky. If I shelled out big money for a car, I would be disappointed to see zip ties, wouldn’t you?

  5. Oh, as for air pumps, these days most cars use cam timing instead of secondary air pumps to initiate faster cat light-off, but as far as I can tell anything that doesn’t have wide enough control of camshaft position and/or super long duration/low overlap cams from the factory (such as, say, high rpm turbo cams) generally seem to be the culprits for secondary air. Still way, wayyyyyyy better than the belt driven smog pumps from back in the day, but… yeah…

    The air pump on my friend’s pristine FB RX-7 is hilariously large 😛

  6. I don’t see which picture you’re referring to that has subframe swaybar mounts in it, but certainly they use the same subframe across all their cars and the 570 series cars have conventional dampers and swaybars.

    1. Top picture of page 4. Basically McLaren made a ‘hole’ in the rear subframe for the sway bar to go through. Looks like a blue polyurethane bushing for the sway bar. I think it’s creative. It keeps the bottom of the car flat instead of having the sway bar poke down into the airflow and the bar is shorter as it doesn’t have to reach around the rear of the transaxle.

  7. Hmmm. Didn’t think they used swaybars with the hydraulic system on the super series. The mp4-12c , the first of their cars to use the hydraulic system, had a z-bar in the rear instead of a swaybar. Maybe this is the same?

    1. Ah, you’re correct. It is a Z-bar. In the last photo in the bottom left corner, you can JUST see the other end of the Z-bar which is behind the rear tie-rod of the left rear spindle indicating it attaches to the back side of the control arm. On the right side, the end of the bar connects to the front side of the control arm.

  8. Macca must be a great place for an engineer, the whole shop is ‘function over form’. They are on another level over there. Makes me wish I was British. Good thing the weather sucks inthe UK.

    1. Yeah, certainly could be! My thought was the water pump was being driven internally in the engine block somehow and that was a clutch between the water pump and that thing on the right. I thought it might be an A/C line going into the thing on the right. But yeah, certainly could be an electric motor on the right driving the water pump on the left.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*