Time to make the hoses. We started by assembling the straight -6 hose end that will connect to the hardline.Next we attach the hose to the hardline and mock up where we’re going to route it. We then use a sharpie to mark where to cut the hose.After cutting the hose and assembling the second hose end, we can install the fuel feed hose.We repeat the process for all the other hose. The fuel filter and fuel pressure regulator were riv-nutted in position.It’s important to blow out all the hoses before installation, especially if you use an angle grinder to the cut the hose like we do.This is what the complete fuel system looks like. We chose to drape the fuel hoses over the brake booster to keep them away from the exhaust.Also, since we are not planning on running a charcoal canister with the SR, we removed the factory fuel breather hardline and simply capped off the fuel tank vent with a filter.
Is there a reason people avoid the AN lines with nylon/fabric braid on the outside? Why risk the damage caused by the steel braid rubbing on damaging things?
I built the 2nd e30 SR20 in North America about 10 years ago, I even still have the wiring harness I made. I also used a Laminova Liquid to air intake manifold, negating the need for an intercooler in the front. I still have the manifold too lol. I used a radiator from a Volvo 240. The heat exchanger for the intercooler was a transmission cooler from and F550 tow truck. It all fit very neatly under the hood. Have fun with brake booster set up, probably the suckiest part of the swap.
Amazing, I have learned lot of things from your website about every thing about cars and how to repair them, I also work at a company in Dubai and learning from your website.
Not enough. It eventually made contact during an aggressive shift (probably flexed the subframe bushings) and snapped the driveshaft.
We are currently looking into shimming the front of the diff down by machining small spacers for the front diff mount and then shimming the trans up to match the pinion angle. Hopefully that will push it a bit further away from the tank (and allow us to run a bigger driveshaft).
what size tailshaft are you aiming for? mine is a 3 inch and it just touches the tank, we have spaced the front diff mounts but we didnt massage the tank so our next step is to massage the tank a little and see how we go.
I know you’re wearing a respirator and gloves, but spraying catalyzed urethane paint is still a potentially hazardous proposition given the isocyanates they contain. All the fun carcinogens (read the MSDS for the paint) you’re atomizing with a spray gun can be absorbed via your skin and eyes, so maybe add a paint suit and DEFINITELY add eye protection next time you do it.
Sorry to be a downer, but it takes pretty minimal overexposure to go from healthy to F’d.
9 comments
Is there a reason people avoid the AN lines with nylon/fabric braid on the outside?
Why risk the damage caused by the steel braid rubbing on damaging things?
I know I don’t!
I built the 2nd e30 SR20 in North America about 10 years ago, I even still have the wiring harness I made. I also used a Laminova Liquid to air intake manifold, negating the need for an intercooler in the front.
I still have the manifold too lol. I used a radiator from a Volvo 240. The heat exchanger for the intercooler was a transmission cooler from and F550 tow truck. It all fit very neatly under the hood.
Have fun with brake booster set up, probably the suckiest part of the swap.
Amazing, I have learned lot of things from your website about every thing about cars and how to repair them, I also work at a company in Dubai and learning from your website.
How much clearence did you have between the tailshaft and the tank? as i have the same setup and im curious.
Not enough. It eventually made contact during an aggressive shift (probably flexed the subframe bushings) and snapped the driveshaft.
We are currently looking into shimming the front of the diff down by machining small spacers for the front diff mount and then shimming the trans up to match the pinion angle. Hopefully that will push it a bit further away from the tank (and allow us to run a bigger driveshaft).
what size tailshaft are you aiming for? mine is a 3 inch and it just touches the tank, we have spaced the front diff mounts but we didnt massage the tank so our next step is to massage the tank a little and see how we go.
We fit a 3″. Had to move the front AND the rear of the diff down. The rear helped the most. We used Garagistic offset diff bushings to move the rear.
I know you’re wearing a respirator and gloves, but spraying catalyzed urethane paint is still a potentially hazardous proposition given the isocyanates they contain. All the fun carcinogens (read the MSDS for the paint) you’re atomizing with a spray gun can be absorbed via your skin and eyes, so maybe add a paint suit and DEFINITELY add eye protection next time you do it.
Sorry to be a downer, but it takes pretty minimal overexposure to go from healthy to F’d.