Resurrecting Project FR-S: Greddy Oil Cooler

We had built some air directors for our radiator and intercooler heat exchanger previously but the trouble is one would have to be removed to make room for the oil cooler and the other would need to be clearanced to make room for the oil cooler hoses.  So we removed the driver’s side director which meant we had to drain the intercooler.

We cut this notch in the air director for the oil cooler hoses.

The oil filter was removed and the thermostat adaptor put in place.  The adaptor simply replaced the oil filter.

Next, the thermostat assembly was installed and clocked toward the front of the car and slightly to the side so the cooler lines could miss the airbox.

You can see why we used the upper fitting locations and blocked the lower ports as the airbox gets in the way of a straight shot for the cooler lines.

For a filter, we used an STP S3614 as the Greddy unit does not use the same filter as the OEM part. This is a filter common with many Toyotas if you wanted to cross-reference to another brand of filter.

19 comments

  1. Great to read another update for this project.

    Do you still have some WiseFab suspension parts to fit to the car?

      1. I’m really looking forward to reading that! Thank you for the time and effort you put into these projects, and sharing the process and results of it all. The knowledge and experience you have shared since the SCC magazine days has always been informative and engaging.

  2. I really like the cooler, but I swear that somebody told me that anodized surfaces didn’t dissipate heat as well. Not sure if I I am remembering that correctly. Also, I would think that black would be the best color for a cooler.

    1. Anodized parts don’t dissipate heat as well. This isn’t anodized, it’s paint. Anodizing works on reactive nonferrous metals. Paint doesn’t dissipate heat as well either and neither does bare aluminum or copper with their natural oxide layer as well. You just can’t win! Black does radiate heat better and there are coatings that enhance this.

  3. Mike, in your opinion whats the highest acceptable oil temp on track for a street/track car (aka not full race car)?

    1. Bearings start to lose load-bearing capacity at 260f oil temp, they melt at around 600 degrees so they start to lose strength by the time the measurable oil temp is around 260. The oil is carrying heat away from the bearings.

      1. From doing lab R&D for a company that solely did bearings, I’d go a bit more conservative than that; 260F is sort of where I’ve seen stuff drop off a cliff. Bearing overlay is already at about half its room temperature strength at 210F. That’s ignoring what you’re doing to your oil viscosity, though this is talking in terms of temperature at the bearing.

  4. I’ve been running my 93 LT1 Camaro past 300 regularly since 2013. In that time I managed to push an oil seal out, run the car low, and spin a rod bearing. The rest of the rods and all the mains were immaculate. I know the science says it’s bad, but my primitive old knuckle dragging V8 doesn’t seem to mind as long as I keep it full. I don’t even run synthetic, just Valvoline VR1 SAE40. Being a dino oil the straight weight helps with stability. Of course this is a track only car.

    There are 2 items in that kit that caught my eye. First was the cooler orientation. With both ports facing up, there’s the possibility of trapping air in there. On my Camaro I put it in rotated 90 degrees with oil in the bottom and out the top. I understand this is not possible with what you have and what you have definitely works. The other thing was the supplied 90 degree fittings. I went with larger mandrel bent 90 degree fittings on mine out of concern for flow and turbulence.

    1. Noticed you hit 300 degrees and you spun a bearing? Wonder why? Your oil temp is a big factor in addition to running low. Bearings start to lose strength after 260F oil temp. If anything happens or not depends on how much reserve you have. Stock engine? Maybe more, On the track or modded? A lot less.

      1. Yes, but I don’t believe the oil temp to have had anything to do with it. The car ended up being a good 2 quarts low and the pickup was JB Welded to the pump and rotated about an inch too high so ignorance on behalf of the PO and me not lifting when I noticed the pressure bouncing mid corner was the cause of death there. 260 is commonly touted as the limit on here but I’m in the minority having an oil cooler at all in my class. I have no doubt that the other cars in my class are hitting 300+ (stock motors) and not blowing up. I’m not advocating to run oil at 300+, but I haven’t seen it be a death sentence myself. I rebuilt the current motor in 2015 and can’t count how many times I’ve raced at 300+. With everyone else doing it, there’s no way it’s luck. I wonder if certain motors are more sensitive than others?

        1. Bigger diameter, and chiefly width, means the bearing is less loaded; 260F isn’t “the metal in the bearings has turned to liquid” but “it’s turned delicate as hell” so being comparatively more gentile helps some. Subaru bearings are terrible by this measure and need all the help they can get.

          1. I should see if I can put together enough not-proprietary data to do a good blog post or something on how bearings work – reciprocating engine bearings are a lot of special cases piled on top of each other. There’s some people who have gone and authoritatively posted a lot of true-but-not-the-full-story data because their engine combination, like many American V8s designed in the 60s, has very generous bearing sizes.

          2. I would love for you to do an article on this. No one ever believes me.

          3. I’ll see what I can put together over the next few weeks; probably will have to make my own diagrams of stuff too, to not violate copyright. But I mean, the best I’ve seen in searchable descriptions is a basic steady state fluid film bearing… which is lovely if we were driving gas turbines but piston engines see peak bearing loads that steady state guidelines say won’t work. Even that has some stuff going on that I’ve seen some engineers just not get; I was fortunate to be able to pick the brains of people with PhDs in the subject.

  5. My point is that, even if stuff is weaker at that temperature, the effect of it isn’t realized in my small world. I believe you guys that stuff happens at 260, but if it isn’t enough to hurt the motor even long term then why get worked up over it? On a good day my oil only gets up to 270. If you do do the article, it would be great to caveat with things like bearing surface area and point out some motors that you know in particular are and are not susceptible to catastrophic failure north of 260. Also bear in mind our GM cars are saddled with restrictor plates, stock motors with stock rev limits when I make these claims.

  6. This seems like a great upgrade and some cheap insurance. My only issue is I hate the idea of taking the front bumper cover off my FR-S, only because so many people have broken the side tabs on them. Did you have any issues refitting the bumper cover back on?

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*