Project S2000: Part 31 – Oil and Fuel System Updates

That transition on the stub reduces the threads which prevents the oil adapter screw from going down far enough to clamp the adapter to the block. I have seen this with both Canton and Mocal oil adapters. The root cause is using the adapter stub. To get the Improved Racing screw to work, I had a buddy machine the length down 4mm.

Here is the adapter all snugged down.

You can see how minimal the Improved Racing adapter is resulting in a compact package. It’s lighter weight too!

The other side of the oil filter relocation equation is the stack of the Improved Racing remote mount, the stock oil cooler, the ARK Design sensor sandwich plate, and the oil filter. The total length is about eight inches.

The stock oil cooler has this little tab on it which orients the cooler properly on the engine block. Here, it prevents the oil cooler from clamping down flush to the Improved Racing remote oil filter mount.

8 comments

    1. The fans are only needed in low-speed operation. Once at speed, there’s enough airflow that the fans are not required. At speed, those shrouds just become a flow resistance and reduce cooling. That particular shroud you linked does have a couple flaps that open up when there’s enough airflow from vehicle speed. In my opinion, shrouds should only be used when the heat exchangers are placed in locations where they don’t get significant direct airflow. So one place shrouds are commonly used is on off-road racing trucks were the radiators are placed behind the cab.

  1. Killerbee catch cans are cool and all, but I can’t comprehend paying $375-$420 bucks for them. Especially when there are alternatives that work flawlessly for $150 or less.

    1. They do command a premium for their billet ones. They have been developing lower cost alternatives like the black one. I’m really digging this new compact AOS which should work well in my application. It seems modern cars with DI systems have much less oil collected in catch cans. The S2k does generate a fair amount, but because I’m planning to constant drain, I don’t really need much storage volume at all.

      1. back into the oil pan? I heard its not a good idea to do that cause it also collects moisture, any truth to that?

        1. I think it depends on the particular vehicle and how their PCV setup is configured. As a casual observation, basic inline and V engines, it’s pretty simple. Flat engines liked in Subarus and Porsches seem to have more complex systems which are maybe more prone to condensation. On my S2k at least, I only ever got significant oil in my catch can from track use and it came out looking like regular oil, no milky stuff. At that point, the oil is hot enough to boil off any water.
          https://motoiq.com/project-s2000-part-22-testing-new-goods-and-more-intake-mods/5/

  2. It’s hard to believe the Improved Racing remote filter mount doesn’t have dedicated additional ports for sensor fittings, especially given the price. Using that ARK adapter adds potential leak paths and bulk. It may be best to utilize the unused ports of the Improved Racing remote filter mount and install adapters for the sensors. You may be able to drill and tap into the top side as well.

    Will running the catch can return line into your turbo drain line overwhelm the turbo drain? You may need to increase the diameter of the return after the tee.

    1. On the remote filter mount, where I’m using two plugs, you can get the plugs with 1/8 NPT sensor ports. The sensors that came with the ARK Design MFD2 are most likely 1/8 BSPT. I decided to leave well enough alone for two reasons: I’ve been running the sandwich plate with sensors for over a decade with no issues and I think it will give me a bit more flexibility in mounting. I’m already claiming space for the oil filter and cooler, so stacking the sensor sandwich plate just takes some more space in the same direction. If I add the sensors to the remote filter mount, they will stick out the opposite side of the oil lines, increasing the footprint. For the turbo oil drain, I was planning to use a -10AN line, so it should be plenty big. I guess I haven’t shown it yet, but the timing chain cover was already tapped and welded with a -10AN fitting for the turbo oil drain return.

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*